Technical guides
Clear explanations of concepts, methods, standards and measurements for engineers and technicians.
- Antennas 52
- Confined spaces 52
- Dielectric materials 54
- Dielectric oils 61
- Electric vehicles 52
- Electrical safety and PPE 52
- Electronic instrumentation 52
- EMC/EMI 53
- Environmental testing 53
- Grounding 54
- Industrial electrical systems 52
- Insulation and high voltage 61
- Metrology and calibration 59
- Oscilloscopes 53
- Power quality and Grid Code 61
- RF and microwave 61
- Solar energy 52
- Temperature and pressure 52
- Thermography 53
- Transformers 55
- Troubleshooting 52
- Vibration 52
- Wireless communications 52
- How is the change in insulation resistance after humidity measured?
It is measured by applying a known DC voltage between conductors insulated from each other and calculating the voltage/current ratio before, during and after humidity exposure, under controlled measurement conditions.
- How is the coexistence of multiple radios in one device tested?
The coexistence of multiple radios in one device is tested by operating the radios simultaneously and comparing the performance of each with its performance in isolation, to detect desensitization, mutual interference and loss of throughput.
- How is the cold junction of a thermocouple compensated?
It is compensated by measuring or fixing the temperature of the reference junction and adding to the thermocouple voltage the voltage that corresponds to that temperature, so that the result is equivalent to a reference junction at zero degrees.
- How is the condition of an insulating mat checked?
An insulating mat is checked by visual and tactile inspection of its entire surface, confirming cleanliness, flexibility, uniform thickness and marking, and by periodic dielectric tests defined by the manufacturer and the applicable regulations.
- How is the connection repeatability of a coaxial connector evaluated?
The connection repeatability of a coaxial connector is evaluated by connecting and disconnecting the same connector several times at a controlled torque, measuring the S-parameters each time, and calculating the spread of the results across the band.
- How is the continuity of a buried ground grid verified?
The continuity of a buried grid is verified by measuring with a low-resistance ohmmeter between accessible points and a reference point on the grid, and comparing the values with one another.
- How is the continuity of protective conductors measured?
The continuity of protective conductors is measured with a low-resistance ohmmeter between the main grounding terminal and each exposed metal part or protective terminal, checking that the value is low and stable.
- How is the crest factor of a current measured?
The crest factor of a current is measured as the ratio of its peak value to its true RMS value in the same window. A pure sine wave gives the square root of two, and higher values indicate the narrow peaks typical of nonlinear loads.
- How is the current in a ground conductor measured?
The current in a ground conductor is measured with a clamp meter that goes around the conductor without opening it, preferably a true-RMS model with sensitivity to small currents.
- How is the dielectric breakdown of an insulating sheet measured?
The dielectric breakdown of an insulating sheet is measured by applying a rising voltage between standardized electrodes until the material fails, and it is expressed as dielectric strength: breakdown voltage divided by thickness.
- How is the dielectric measurement method chosen according to frequency?
The dielectric measurement method is chosen according to the frequency range: at low frequency, parallel-plate cells with an impedance bridge are used; at radio and microwave frequencies, the choice moves to probes, transmission lines, free space or resonant cavities.
- How is the distortion a charger generates on the grid measured?
The distortion a charger injects into the grid is measured with a power quality analyzer at the AC input, logging current harmonics, total distortion and power factor at different power levels throughout the charging session.
- How is the effect of a distributed generation plant on the local grid assessed?
It is assessed by comparing the state of the local grid with and without the plant, at the connection point, reviewing voltage level, power flows, protections, waveform quality, and behavior during faults.
- How is the effect of distance compensated for?
Distance has two effects: the object occupies fewer pixels and is averaged with the background, and the air attenuates the signal. It is compensated by moving closer, using a longer focal length and entering the real distance.
- How is the efficiency of a charger measured?
The efficiency of a charger is the active output power divided by the active input power, measured at the same time with a power analyzer and at different load levels.
- How is the electrical installation for chargers sized?
The installation for chargers is sized from the power and voltage of each charger, treating the load as continuous, with suitable conductors, protective devices and transformer, and considering load management when there are several units.
- How Is the Electrical Length of an Antenna Cable Measured?
The electrical length of a cable is measured with an analyzer in the frequency or time domain: the signal delay or the phase shift into an open or shorted load is determined and then related to the physical length through the velocity factor.
- How is the electrical safety of a battery pack tested?
The electrical safety of a pack is verified with insulation resistance measurements, dielectric strength tests, ground continuity and functional checks of the battery management system's protection functions.
- How is the emissivity of a surface determined in the field?
Emissivity is determined in the field by comparing the camera reading with a known temperature of the same surface, or by applying a material of known emissivity and adjusting until the readings match.
- How is the five whys technique applied?
The five whys technique consists of asking “why?” repeatedly, each time about the previous answer, until reaching a cause that can be acted on.
- How is the frequency error of a transmitter measured?
The frequency error of a transmitter is measured by comparing its actual frequency with the nominal one using an instrument with a stable time base, and it is expressed in hertz or in parts per million relative to the center frequency.
- How is the frequency of an oscillator measured accurately?
With a frequency counter whose time base is much more accurate than the oscillator being measured, ideally synchronized to a common external reference, and with a gate time sufficient for the desired resolution.
- How is the front-to-back ratio measured?
The front-to-back ratio is obtained from the radiation pattern: it is the difference, in decibels, between the level in the direction of maximum radiation and the level in the opposite direction, at 180 degrees.
- How is the grounding of a laboratory with sensitive equipment verified?
By checking the continuity of the protective conductors, the electrode resistance, the location of the neutral-to-ground bond, and the potential differences and currents between the grounds that supply or reference the sensitive equipment.
- How is the group delay of a filter measured?
The transmission phase is measured across frequency and its negative slope is calculated; group delay indicates how much the signal envelope is delayed at each frequency and reveals the phase distortion of the filter.
- How is the homogeneity of a laminate verified?
The homogeneity of a laminate is verified by comparing a property at different points and layers, and by complementing this with non-destructive inspection and cross-sections, to detect voids and variations in thickness and in resin or reinforcement content.
- How Is the Hysteresis of an Instrument Measured?
Hysteresis is measured by applying the same values of the quantity in increasing and then decreasing order and comparing the indications at each point: the difference between the two paths is the hysteresis.
- How is the I-V curve measured in the field?
A curve tracer is connected to the PV module or string and sweeps the load from short circuit to open circuit while irradiance and temperature are measured at the same time, so the results can be compared with reference conditions.
- How Is the Indication Error of an Instrument Determined?
Indication error is determined by comparing the instrument reading with the value of a traceable standard at several points across the span; the error is the indication minus the reference value, and it is reported together with its uncertainty.
- How is the input impedance of an antenna measured?
Input impedance is measured by connecting the antenna to a vector network analyzer, previously calibrated at the connector plane, and reading the complex reflection coefficient as a function of frequency, from which the impedance is calculated.