24/7 emergencies 814 777 6921812 230 6079WhatsApp 811 786 0768
Electrónica MonterreyElectrónica MonterreyLaboratorios Creativeit Talk to an engineer
Menu

Environmental testing

Clear explanations of concepts, methods, standards and measurements for engineers and technicians.

  • Accelerated life test or test under real conditions?

    An accelerated test obtains results in less time by raising stresses, while a test under real conditions is more faithful but slow. The choice depends on whether the failure mechanism is preserved when accelerating.

  • Chamber test or field test?

    It depends on the question you want to answer: an environmental chamber isolates and repeats a controlled condition, while a field test shows how the equipment behaves with all the real conditions combined.

  • Constant humidity or cyclic humidity?

    Constant humidity evaluates the effect of a stable humid atmosphere over a long period; cyclic humidity alternates temperature and humidity to cause condensation and enclosure breathing, and is more severe for many products.

  • Continuous or cyclic salt spray?

    Continuous salt spray keeps the exposure constant and is used for control and comparison; cyclic salt spray alternates fog, drying and humidity and better reproduces real atmospheric corrosion.

  • How a dry heat test is performed

    The sample is brought to a high temperature in a chamber with low-humidity air, held until its interior stabilizes, and checked for condition and operation, either during exposure or afterward.

  • How a dust exposure test is performed

    The enclosure is exposed to standardized dust in a chamber that keeps it in suspension or blows it onto the sample, with or without an internal pressure difference, and it is then checked for dust ingress and for correct operation of the equipment.

  • How a mechanical shock test is performed

    The sample is subjected to a brief acceleration impulse with a defined pulse shape, amplitude and duration, applied in specified directions, and is then checked, or monitored during the event, for damage or loss of function.

  • How a sample is conditioned before a climatic test

    The sample is brought to a known, repeatable initial state, normally at stable ambient temperature and humidity for a sufficient time, with initial measurements recorded, so that the result depends on the test and not on its previous history.

  • How a sample is monitored during a long-duration test

    The environmental conditions and the behavior of the sample are recorded continuously with calibrated instruments, alarms and a response plan, in order to detect a failure the moment it occurs and understand how it developed.

  • How an environmental test profile is defined for a product

    The starting point is the real environment the product will see during its life. The most severe or damaging events are translated into test conditions, and levels, ramps and duration are justified with the standard, the customer requirement or measured data.

  • How are intermittent failures recorded during an environmental test?

    An intermittent failure is recorded by monitoring the product's function continuously, with sufficient time resolution, while the environment changes, and by storing each event with a timestamp.

  • How does a salt spray chamber work?

    A salt spray chamber atomizes a sodium chloride solution inside a temperature-controlled enclosure, so that the parts become coated with a wet saline film that accelerates corrosion.

  • How is a luminaire tested for severe weather conditions?

    A luminaire is tested for severe weather by combining temperature and humidity, water and dust ingress, corrosion, radiation and vibration tests, and verifying that it maintains its optical, thermal and electrical function.

  • How is an automotive component environmentally qualified?

    An automotive component is environmentally qualified by defining its mission profile and location in the vehicle, and subjecting it to temperature, humidity, vibration, dust, water and chemical tests consistent with that profile.

  • How is an environmental qualification plan prepared?

    An environmental qualification plan is prepared by defining the product and its life environment, the failure modes to uncover, the test sequence, the sample size, the acceptance criteria and the documentation of results.

  • How is an outdoor product validated?

    An outdoor product is validated by identifying the environmental factors it will face, translating them into representative tests and verifying function and degradation after combined exposure.

  • How is electronic equipment for vehicle use tested?

    Electronic equipment for vehicles is tested by combining environmental tests, such as temperature, vibration and humidity, with electrical power supply and electromagnetic compatibility tests that reflect the conditions of the onboard electrical system.

  • How is the change in insulation resistance after humidity measured?

    It is measured by applying a known DC voltage between conductors insulated from each other and calculating the voltage/current ratio before, during and after humidity exposure, under controlled measurement conditions.

  • How is the leak tightness of an enclosure measured after a test?

    Leak tightness is measured by detecting the flow of a gas through the enclosure, whether by pressure decay, by flow change or with a tracer gas, and comparing it with the allowable leak criterion.

  • How is the thermal stabilization time of a sample determined?

    Thermal stabilization time is determined by measuring the temperature of the slowest point of the sample, normally its core, during a trial run, and observing when it approaches the target value within tolerance and stops changing appreciably.

  • How sinusoidal and random vibration tests are performed

    The sample is attached to a shaker with a fixture and vibrated with a sinusoidal signal, which sweeps or holds frequencies, or a random signal, which excites many frequencies at once, under accelerometer control.

  • How temperature uniformity is measured inside a chamber

    An array of calibrated sensors is placed in the working volume, the chamber is stabilized at the setpoint, and the difference between the hottest and coldest sensors at the same instant is calculated over a recording period.

  • How the rate of temperature change is measured in a chamber

    Temperature is recorded with sensors in the chamber air and on the sample during a ramp, and the slope is calculated over a defined interval, distinguishing the air rate from the rate the sample actually reaches.

  • How water splash resistance is tested

    The enclosure is sprayed with water from several directions, using a device and flow rate set by the standard, for a defined time, and it is then checked for water ingress and for continued operation of the equipment.

  • Sinusoidal or random vibration?

    Sinusoidal vibration excites one frequency at a time, which is ideal for finding resonances; random vibration excites all of them at once with a defined spectral density and more closely resembles a real environment.

  • What a cold operation test is

    A cold operation test verifies that equipment starts and operates correctly while subjected to low temperature, unlike cold storage, where the only check is that it survives.

  • What an accelerated life test is

    An accelerated life test subjects a product to stresses higher than those of normal use to trigger, in a short time, the same failure mechanisms that would occur over years, and from that to estimate its life under normal conditions.

  • What an environmental test profile is

    An environmental test profile is the time-defined sequence of conditions applied to a sample, such as temperature, humidity and vibration, with their values, rates of change and durations.

  • What causes a circuit board to delaminate after humidity exposure?

    Delamination occurs because the laminate absorbs moisture and, when it is heated, steam and stresses separate the layers, especially if the bond between resin and reinforcement was already weak.

  • What condensation is and why it damages equipment

    Condensation occurs when a surface falls below the dew point of the surrounding air and the vapor turns into liquid water on it. That water causes corrosion, leakage and short circuits.

We do real tests, on video! Watch them on our YouTube channel →

Do you have a problem nobody has been able to measure?

Talk directly to the engineer in charge, with no middlemen.

Talk to an engineer