24/7 emergencies 814 777 6921812 230 6079WhatsApp 811 786 0768
Electrónica MonterreyElectrónica MonterreyLaboratorios Creativeit Talk to an engineer
Menu

Temperature and pressure

Clear explanations of concepts, methods, standards and measurements for engineers and technicians.

  • Analog pressure gauge or digital transmitter: which is the right choice

    An analog pressure gauge serves for local indication without power; a digital transmitter serves when the pressure must reach a control system, a record or an alarm. The choice depends on who needs the data and where.

  • Gauge or absolute pressure for an application?

    Gauge pressure is chosen when the difference from the surroundings matters, and absolute pressure when the value relative to vacuum matters; the key is whether variation in atmospheric pressure affects what you want to know.

  • How a compressed air line is checked for leaks

    Leaks are located with ultrasonic detection or soap solution, and their size is quantified by measuring consumption with the process stopped or the pressure drop in a known volume.

  • How a pressure vessel is tested before operation

    It undergoes a pressure test, normally hydrostatic, under an approved procedure, with inspection for leaks and deformation and recording of the results. The test must be done by qualified personnel in accordance with the design code.

  • How does a pressure transmitter work?

    A pressure transmitter converts process pressure into a standardized electrical signal: a sensing element deforms, the electronics condition that deformation and deliver an output, commonly a loop current.

  • How does a thermocouple work?

    A thermocouple works because two different metals or alloys, joined at one end, generate a voltage that depends on the temperature difference between that end and the other, through the Seebeck effect.

  • How does an RTD temperature sensor work?

    An RTD measures temperature by taking advantage of the fact that the electrical resistance of a metal, normally platinum, increases in a stable and repeatable way as temperature rises.

  • How does the resistance of a metal vary with temperature?

    The electrical resistance of a metal increases with temperature almost linearly over a moderate range, because the greater agitation of the crystal lattice scatters the conduction electrons more.

  • How is a pressure decay leak test performed?

    The test pressurizes the system, isolates it and monitors how much the pressure falls over a defined time, carefully distinguishing a drop caused by a real leak from one caused by temperature changes.

  • How is a pressure gauge calibrated with a deadweight tester?

    A deadweight tester generates a known pressure with a piston and cylinder loaded with calibrated masses; the gauge is connected to the same circuit and its reading is compared with that pressure.

  • How is a pressure transmitter verified at its installation site?

    It is verified by isolating the transmitter from the process, applying known pressures with a source and a reference standard, and comparing the applied pressure with the transmitter's output, normally the loop current, at several points across the range.

  • How is a resistance thermometer calibrated by comparison?

    It is calibrated by comparing the resistance thermometer's readings with those of a reference standard, both immersed in a stable isothermal medium, at several temperatures spread across the range of use.

  • How is air bled from a hydraulic test circuit?

    Air is bled by filling the circuit from the lowest point, venting at the high points and moving the fluid until it comes out free of bubbles, because air is compressible and makes pressure tests slow and unstable.

  • How is differential pressure measured across a filter?

    Differential pressure across a filter is measured with two taps, one before and one after the filter element, connected to a differential sensor; the difference grows as the filter gets dirty and is a guide to when to replace it.

  • How is level measured with a hydrostatic sensor?

    A hydrostatic sensor measures level because the pressure at the bottom of a liquid is proportional to its height and density; with the density and gravity known, the measured pressure is converted into liquid height.

  • How is relative humidity measured accurately?

    Measuring relative humidity well requires measuring temperature well, because relative humidity is a ratio between the vapor pressure present and the saturation vapor pressure, and the latter changes greatly with temperature.

  • How is surface temperature measured by contact?

    Surface temperature is measured by contact by ensuring good thermal contact between the sensor and the surface and preventing the sensor from altering it; errors almost always come from that imperfect contact and from losses through the sensor itself.

  • How is temperature measured with a thermocouple?

    Temperature is measured with a thermocouple by connecting it, with the correct cable type and polarity, to an instrument that compensates the reference junction and converts voltage to temperature; quality depends above all on the connections and the installation.

  • How is the calibration point of a sensor chosen?

    The calibration point is chosen according to how the sensor will be used: the points must cover the actual working range, include the most critical process value and be enough to reveal the sensor's behavior, which depends on whether it is linear or not.

  • How is the cold junction of a thermocouple compensated?

    It is compensated by measuring or fixing the temperature of the reference junction and adding to the thermocouple voltage the voltage that corresponds to that temperature, so that the result is equivalent to a reference junction at zero degrees.

  • How is vacuum pressure measured?

    Vacuum pressure is measured with the sensor suited to the pressure range: diaphragm gauges in low and medium vacuum, thermal gauges in an intermediate range and ionization gauges in high vacuum; many of them depend on the type of gas.

  • How server room temperature is monitored

    A network of sensors is placed at the points where air enters the equipment, not just at the air conditioning return, with continuous logging, alarms and trend review.

  • How temperature distribution in a chamber is validated

    A grid of calibrated sensors is placed in the working volume, the chamber is stabilized, and the deviation and variation of each point from the setpoint are analyzed over a period long enough to reveal drift.

  • How temperature is measured in an industrial furnace

    It is measured with sensors placed where they represent the load or the process, not just the furnace air, and uniformity is verified with a multi-sensor survey. The sensor type depends on the range and the atmosphere.

  • Liquid bath or dry block for calibrating probes

    A liquid bath offers better thermal uniformity and accepts probes of various shapes; a dry block is more portable and faster, but its accuracy depends on the fit between the probe and the well.

  • Piezoresistive or capacitive pressure sensor?

    A piezoresistive sensor measures diaphragm deformation with gauges whose resistance changes, and a capacitive sensor with the change in capacitance between diaphragm and plate; the former is rugged and general-purpose, and the latter stands out at low and differential pressures.

  • RTD or thermocouple for a process?

    The choice depends on the temperature range, accuracy, response time and mechanical conditions: the RTD usually wins on accuracy and stability, and the thermocouple on range, ruggedness and speed.

  • What are absolute, gauge and differential pressure?

    The three differ in the reference they are measured against: absolute pressure is measured against a perfect vacuum, gauge pressure against local atmospheric pressure and differential pressure between any two process pressures.

  • What causes a pressure gauge to stick under pulsation

    Pulsation fatigues the mechanism and causes wear, play and an unstable or stuck pointer. A damper or a fill fluid reduces the effect, but neither replaces choosing the right gauge.

  • What guidance ASME B40.100 gives on pressure gauges

    ASME B40.100 deals with indicating pressure gauges with elastic elements: their types, accuracy classes, dimensions, construction and marking, as a general reference for manufacturers and users.

We do real tests, on video! Watch them on our YouTube channel →

Do you have a problem nobody has been able to measure?

Talk directly to the engineer in charge, with no middlemen.

Talk to an engineer