- Antennas 52
- Confined spaces 52
- Dielectric materials 54
- Dielectric oils 61
- Electric vehicles 52
- Electrical safety and PPE 52
- Electronic instrumentation 52
- EMC/EMI 53
- Environmental testing 53
- Grounding 54
- Industrial electrical systems 52
- Insulation and high voltage 61
- Metrology and calibration 59
- Oscilloscopes 53
- Power quality and Grid Code 61
- RF and microwave 61
- Solar energy 52
- Temperature and pressure 52
- Thermography 53
- Transformers 55
- Troubleshooting 52
- Vibration 52
- Wireless communications 52
- AC or DC for an Applied Voltage Test?
AC voltage reproduces service stress but requires a source that can supply the capacitive current; DC requires a small source and measures leakage, although it distributes the field differently.
- DC or Very Low Frequency Testing on Cables?
For extruded medium-voltage cables, very low frequency is usually preferred over direct current, because it distributes the field as in service and avoids the space charge that DC leaves in the insulation.
- Diagnostic Test or Pass/Fail Test?
A pass/fail test confirms that the insulation withstands a defined stress level; a diagnostic test measures parameters that describe its condition and makes it possible to follow its evolution.
- How are the acceptance criteria for an insulation test defined?
The acceptance criteria for an insulation test are defined before measuring, by combining the requirements of the standard or manufacturer, the equipment's history and the test conditions, and they are documented together with the method.
- How Are the Capacitance and Dissipation Factor of a Cable Measured?
The capacitance and dissipation factor of a cable are measured by applying AC voltage between conductor and shield with a bridge or digital instrument that separates the capacitive current from the loss current.
- How Do You Correct Insulation Resistance for Temperature?
Insulation resistance falls as temperature rises, so it is corrected by multiplying the reading by a coefficient that brings it to a common reference temperature.
- How Do You Interpret the Insulation Resistance Trend Over Time?
The insulation resistance trend is interpreted by comparing readings from the same equipment, taken under equivalent conditions and corrected for temperature; the direction and speed of the change matter more than an isolated value.
- How Do You Locate a Fault in an Underground Cable?
A fault in an underground cable is located in stages: confirm the type of fault, estimate its distance from one end, and finally pinpoint it along the route.
- How Do You Prepare an Insulation Resistance Test on Energizable Equipment?
To prepare an insulation resistance test, de-energize, verify the absence of voltage, isolate the equipment from other circuits, clean it and record the conditions before applying the test voltage.
- How Do You Safely Discharge Equipment After an Insulation Test?
After an insulation test, the equipment retains charge in its capacitance, so it is discharged in a controlled way and kept grounded for a time before it is handled.
- How Does a High-Voltage Divider Work?
A high-voltage divider uses two series impedances to reduce a high voltage to a small, proportional voltage that can be measured with a conventional instrument.
- How Does a Marx Impulse Generator Work?
A Marx generator charges several capacitors in parallel and discharges them in series through spark gaps, so that the output voltage is approximately the sum of the charging voltages of each stage.
- How Does a Megohmmeter Work?
A megohmmeter generates a high DC voltage, applies it to the insulation under test, measures the tiny current that flows and displays the resistance obtained from Ohm's law.
- How Does a Schering Bridge Work?
The Schering bridge compares an unknown lossy capacitor with a nearly lossless standard capacitor; when the detector indicates balance, the components of the adjustable arm give the capacitance and the dissipation factor.
- How does an AC high-voltage tester work for insulation testing?
An AC high-voltage tester applies an adjustable alternating voltage to the insulation, generated by a step-up transformer, and measures the current flowing; if that current exceeds a set limit or a discharge occurs, the unit disconnects and signals the failure.
- How Does Solid Insulation Age Under Electrical Stress?
Solid insulation ages under electrical stress through cumulative damage: partial discharges in voids erode the material, branching channels (trees) form, and the sound thickness shrinks until breakdown occurs.
- How is a generator evaluated before returning to service after a flood?
A flooded generator is evaluated without energizing it: the damage is documented, the machine is cleaned and dried in a controlled way, and insulation resistance is monitored until it can be decided whether to return it to service, rewind it or replace it.
- How Is a Guard Applied in an Insulation Measurement?
A guard is applied by connecting the surfaces or conductors that carry surface leakage to the guard terminal, so that this current is diverted and does not add to the measurement.
- How is a new cable verified before commissioning?
A new cable is verified by checking its physical condition, jacket integrity, insulation, continuity and phase sequence, and then applying the withstand test specified by the project.
- How is a step voltage test performed on insulation?
A step voltage test applies a series of increasing DC voltages to the insulation, holding each one for the same time, and compares the insulation resistance at each step: sound insulation keeps its resistance almost constant, while defective insulation shows the resistance falling as the voltage rises.
- How Is an Applied Voltage Test Performed?
In an applied voltage test, the insulation is subjected to a voltage above the service voltage, between conductors and ground, for a defined time; if there is no breakdown, the equipment passes.
- How is electric stress distributed between the layers of an insulation system?
When several insulation layers are in series, the AC electric field is distributed inversely to the permittivity of each layer, so the layer with the lowest permittivity carries the highest field. Under direct current, the distribution is determined by the resistivities.
- How Is Leakage Current Measured During a DC Test?
Leakage current in a DC test is measured with a microammeter at the source and interpreted by separating capacitive charging, absorption and conduction, the component that reveals the condition of the insulation.
- How Is the Breakdown Voltage of an Insulator Measured?
The breakdown voltage of an insulator is determined by raising the test voltage until a disruptive discharge occurs, repeating the test and applying corrections for atmospheric conditions.
- How is the insulation of a current transformer tested in the field?
The insulation of a current transformer is tested in the field with the equipment de-energized and isolated, by measuring the insulation resistance between windings and to ground and, where possible, the capacitance and dissipation factor of the main insulation through the test tap.
- How is the insulation of a DC battery bank verified?
In a DC battery bank, insulation is verified with the system in service, using ground fault detection or the measurement of voltages to ground, because a floating system tolerates a first fault but not a second.
- How is the insulation of medium-voltage switchgear tested?
The insulation of medium-voltage switchgear is tested with the equipment de-energized, isolated and grounded, removing or isolating sensitive components, and measuring between phases and from each phase to ground.
- How Is the Insulation Resistance of a Medium-Voltage Cable Measured?
The insulation resistance of a medium-voltage cable is measured between each conductor and its grounded shield, with the cable de-energized and isolated at both ends.
- How Is the Insulation Resistance of a Motor Measured?
The insulation resistance of a motor is measured with the motor de-energized and disconnected from its supply cable, by applying DC voltage between the windings and the grounded frame.
- How Is the Lightning Impulse Waveform Measured?
The waveform of a lightning impulse is measured with a voltage divider and a high-speed recorder, and is characterized by its front time, its time to half-value and its overshoot.