24/7 emergencies 814 777 6921812 230 6079WhatsApp 811 786 0768
Electrónica MonterreyElectrónica MonterreyLaboratorios Creativeit Talk to an engineer
Menu

Antennas

Clear explanations of concepts, methods, standards and measurements for engineers and technicians.

  • Anechoic Chamber or Open-Area Test Site?

    An anechoic chamber offers a controlled environment protected from external noise and weather, while an open-area site allows large equipment to be measured with a known ground reflection but exposes the measurement to ambient noise.

  • Dipole or Monopole Antenna?

    A dipole is a two-arm antenna that needs no ground plane; a monopole is a single arm over a conductive plane that, by the image principle, behaves like half a dipole, with half the theoretical impedance.

  • How Do You Choose an Antenna for Industrial Telemetry?

    For industrial telemetry, an antenna is chosen based on the radio band, the link geometry, the environment and the type of installation: normally an omnidirectional antenna for a hub and directional antennas for fixed links, with attention to the link budget.

  • How Do You Locate an Interference Source with a Directional Antenna?

    An interference source is located by moving a directional antenna and watching on a spectrum analyzer where the signal is strongest: the direction is obtained by taking a bearing, and the position by triangulation from several points.

  • How Does a Reference Horn Antenna Work?

    A horn antenna is a waveguide that flares gradually out to an aperture, so that the guided wave is transformed into a radiated wave with a smooth transition and highly predictable directivity, which makes it useful as a reference standard.

  • How is a link budget calculated?

    The transmitted power and the antenna gains are added in decibels, and all the path losses, including free-space loss, are subtracted. The result is the received power, which is compared with the receiver sensitivity to obtain the margin.

  • How is a point-to-point link aligned?

    Direct line of sight with a clear Fresnel zone is ensured, the antennas are roughly pointed using geographic references, and each antenna is then fine-tuned in azimuth and elevation until the received signal is maximized, confirming that it is the main lobe.

  • How is a radiation pattern measured in an anechoic chamber?

    The antenna under test is mounted on a positioner that rotates it inside the chamber, it is illuminated by a probe antenna at far-field distance, and the received signal is recorded as a function of angle with a network analyzer or a receiver.

  • How is an antenna array designed?

    The radiating element, its spacing and the amplitude and phase excitation of each element are chosen. The pattern of the whole is the element pattern multiplied by the array factor, which depends on the geometry and on those excitations.

  • How Is an Antenna Installed on a Tower Verified?

    An antenna installed on a tower is verified by using a cable and antenna analyzer to measure the return loss and distance to fault of the complete line, and by checking the antenna's orientation, tilt and any mechanical damage.

  • How Is an Antenna Integrated into a Product Designed?

    The design of an antenna integrated into a product starts from the available space and materials: the band is defined, a compact type is chosen, it is simulated with the actual housing and circuit, and it is adjusted with measurements on the prototype.

  • How is an antenna tuned to a target frequency?

    The reflection of the antenna is measured with a network analyzer, the resonant frequency is located and its electrical length is modified: shortening it raises the resonance and lengthening it lowers it. Corrections are made in small steps with the antenna installed.

  • How Is an Antenna Used in Emissions Testing?

    In emissions testing, the antenna acts as a transducer that converts the field radiated by the equipment under test into a voltage a receiver can measure; its antenna factor is used to calculate the field strength, which is compared with the limit.

  • How is an open-field antenna measurement performed?

    The antenna under test and a reference antenna are installed at far-field distance, on non-metallic supports and on clear ground, and ground reflection and ambient signals, the two main sources of error, are controlled.

  • How is antenna gain measured with three antennas?

    The three-antenna method obtains the gain of three unknown antennas by measuring the transmission between them in pairs and solving a system of three equations, without needing an antenna of known gain.

  • How is cross-polarization measured?

    Cross-polarization is measured by recording the antenna pattern with a probe of the same polarization as the antenna (co-polar) and then with an orthogonal probe, and comparing the two levels in each direction.

  • How is gain determined by comparison?

    The received signal is measured with an antenna of known gain and then with the antenna under test, in the same geometry. The difference in decibels between the two readings, added to the gain of the reference, gives the gain of the antenna under test.

  • How Is the Electrical Length of an Antenna Cable Measured?

    The electrical length of a cable is measured with an analyzer in the frequency or time domain: the signal delay or the phase shift into an open or shorted load is determined and then related to the physical length through the velocity factor.

  • How is the front-to-back ratio measured?

    The front-to-back ratio is obtained from the radiation pattern: it is the difference, in decibels, between the level in the direction of maximum radiation and the level in the opposite direction, at 180 degrees.

  • How is the input impedance of an antenna measured?

    Input impedance is measured by connecting the antenna to a vector network analyzer, previously calibrated at the connector plane, and reading the complex reflection coefficient as a function of frequency, from which the impedance is calculated.

  • How Is the Isolation Between Two Nearby Antennas Measured?

    Isolation is measured by connecting each antenna to one port of a network analyzer and measuring the transmission parameter between the two ports; the lower the transmission, the higher the isolation.

  • Linear or Circular Polarization?

    Linear polarization keeps the electric field oscillating in a fixed direction; circular polarization makes it rotate. Linear is chosen when both ends hold a stable orientation, and circular when the orientation varies or rotation must be tolerated.

  • Omnidirectional or directional antenna?

    It depends on whether coverage must reach every direction in the horizontal plane or be concentrated toward one point: the omnidirectional antenna spreads the energy over 360 degrees with shorter range, and the directional antenna concentrates it with more gain in one direction.

  • Patch Antenna or Yagi Antenna?

    A patch antenna is flat, compact and of moderate gain, ideal for integrating into surfaces or circuits; a Yagi is a structure of parallel elements with more directional gain, but it is bulkier and has a narrower band.

  • What Causes the Multipath Effect?

    Multipath occurs when the signal reaches the receiver by several paths (direct, and reflected or diffracted by buildings, the ground or objects), and the copies, with different delays and phases, add or subtract, producing fading and intersymbol interference.

  • What Does CISPR 16-1-4 Specify for Measurement Antennas?

    CISPR 16-1-4 sets requirements for the antennas and test sites used to measure radiated disturbances, so that emissions measurements made in different laboratories are comparable.

  • What does dBi mean?

    dBi means decibels relative to an isotropic radiator: it expresses, on a logarithmic scale, how many times the antenna concentrates power in one direction compared with an ideal antenna that radiates equally in all directions.

  • What Does the IEC 62232 Standard Assess for Base Stations?

    IEC 62232 deals with determining radio-frequency field strength, power density and specific absorption rate near radiocommunication base stations, in order to assess human exposure to electromagnetic fields.

  • What Does the IEEE 145 Standard Define for Antennas?

    IEEE 145 is a document of definitions of terms for antennas: it establishes a common vocabulary for concepts such as gain, directivity, radiation pattern and polarization, so that results are interpreted the same way by laboratories and manufacturers.

  • What Is a Balun Used For?

    A balun is used to connect an unbalanced line, such as a coaxial cable, to a balanced antenna or load, preventing common-mode currents from flowing on the cable shield and altering the pattern and impedance.

We do real tests, on video! Watch them on our YouTube channel →

Do you have a problem nobody has been able to measure?

Talk directly to the engineer in charge, with no middlemen.

Talk to an engineer