24/7 emergencies 814 777 6921812 230 6079WhatsApp 811 786 0768
Electrónica MonterreyElectrónica MonterreyLaboratorios Creativeit Talk to an engineer
Menu

Technical guides

Clear explanations of concepts, methods, standards and measurements for engineers and technicians.

  • How is radiated emission measured at a test distance?

    The field strength of the equipment is measured with an antenna at a defined distance and a receiver, rotating the equipment and varying the height and polarization of the antenna to record the maximum. The antenna and cable factors are then applied and the result is compared with the limit at that distance.

  • How is reactive power measured in unbalanced loads?

    Reactive power in unbalanced loads is measured per phase, using the voltage and current of each phase, and then summed. The delicate part is that under unbalance, total apparent power and total power factor have several definitions that are not equivalent.

  • How is received signal strength measured?

    Received signal strength is measured with a calibrated receiver that indicates the power or voltage at its input, or with a field antenna of known response; the value depends on the antenna, the bandwidth and the calibration.

  • How is receiver sensitivity determined?

    The sensitivity of a receiver is the minimum signal it needs to reach a defined quality level, normally a given error rate; it is determined by reducing the level of a known signal until the quality just reaches that limit.

  • How is relative humidity measured accurately?

    Measuring relative humidity well requires measuring temperature well, because relative humidity is a ratio between the vapor pressure present and the saturation vapor pressure, and the latter changes greatly with temperature.

  • How is relative shaft vibration measured?

    Relative shaft vibration is measured with proximity sensors that do not touch the shaft and that record its motion relative to the casing or bearing on which they are mounted, something an accelerometer on the casing does not see as clearly.

  • How is residual core magnetization measured?

    The core retains part of the magnetic flux after a disconnection or a direct current test; it is estimated by injecting controlled direct current and integrating the induced voltage, and it is removed by demagnetization.

  • How is resistivity measured in stratified soils?

    In stratified soil, resistivity is measured by repeating the four-electrode array at increasing spacings, and the apparent resistivity curve is interpreted to estimate the thickness and resistivity of each layer.

  • How is risk assessed in an old electrical panel?

    Risk in an old panel is assessed by comparing what the equipment can withstand with what the system demands of it today: interrupting rating against available short-circuit current, physical condition of connections and insulation, and arc incident energy.

  • How is rotational speed measured with a tachometer?

    A tachometer measures rotational speed by counting how many times per unit of time a mark or reflection passes its sensor, or by measuring the linear speed of a surface in contact, and it expresses the result in revolutions per minute.

  • How is shading measured at a site?

    Shading at a site is measured by determining which part of the horizon and nearby objects blocks the sun at each moment of the year, using horizon survey tools or photographic analysis, and is expressed as an irradiation loss.

  • How is shaft displacement measured?

    Shaft displacement is measured with non-contact proximity sensors, which convert the distance between the sensor tip and the metal surface of the shaft into an electrical signal, both for its average position and for its vibratory motion.

  • How is signal integrity evaluated on a digital line?

    Signal integrity on a digital line is evaluated by observing, at the receiver, the edge shape, overshoot, ringing from reflections, noise and jitter, with a bandwidth and probe connection that do not distort what is being measured.

  • How is soiling loss evaluated?

    Soiling loss is evaluated by comparing the output of a clean module or cell with that of an identical one exposed without cleaning. The ratio between the two, normally of the short-circuit current, gives the fraction of energy lost to dust.

  • How is solar inverter interference with a radio resolved?

    First identify how the disturbance reaches the radio (through the DC cables, through the AC output or by radiation), then cut that path with filtering, ferrites on the cables, better routing and grounding, as well as by moving the antenna away from the inverter cables.

  • How is step-by-step fault diagnosis structured?

    Orderly fault diagnosis moves from the general to the particular: describe the symptom, gather data without altering the equipment, form hypotheses, test them one by one and confirm the correction.

  • How is surface temperature measured by contact?

    Surface temperature is measured by contact by ensuring good thermal contact between the sensor and the surface and preventing the sensor from altering it; errors almost always come from that imperfect contact and from losses through the sensor itself.

  • How is surface tracking resistance measured?

    Surface tracking resistance is measured by subjecting the surface of the insulator to voltage and to controlled wet contamination, and observing whether conductive paths form or whether the material fails under a defined criterion.

  • How is tap changer contact resistance measured?

    It is measured by injecting direct current into the winding through the tap changer and recording the voltage drop at each position, in order to compare contact quality across positions and phases.

  • How is temperature difference measured against a similar reference?

    Measure the temperature of the suspect component and of an identical one under the same load and conditions, then compare the difference; this removes the effect of the ambient and of the common load.

  • How is temperature measured through an infrared window?

    To measure through an infrared window, use an infrared-transparent material, tell the camera the window transmittance, and pay attention to its cleanliness, angle and temperature.

  • How is temperature measured with a thermocouple?

    Temperature is measured with a thermocouple by connecting it, with the correct cable type and polarity, to an instrument that compensates the reference junction and converts voltage to temperature; quality depends above all on the connections and the installation.

  • How Is Temporary Overload Capability Determined?

    Temporary overload capability is determined with a thermal model that starts from the prior load, the ambient temperature and the oil and winding time constants; it is limited by the hot spot, aging and the accessories.

  • How is the absence of voltage verified before starting work?

    The absence of voltage is verified by testing a suitable instrument on a known source, measuring on every conductor that will be touched and then testing the instrument again, because a single no-voltage result may be due to a faulty instrument.

  • How is the atmosphere assessed before entry?

    It is assessed with a calibrated gas detector, testing the atmosphere from outside at different levels of the space, measuring oxygen first, then flammable gases and then toxic gases, and monitoring continues for as long as anyone is inside.

  • How is the audible noise level of a transformer measured?

    The audible noise level of a transformer is measured with a sound level meter at points distributed around the unit at a defined distance, with A-weighting, and corrected for background noise to obtain a representative average value.

  • How is the available fault current at a panel measured?

    The available fault current at a panel is normally obtained by short-circuit calculation using system data; in the field it can only be estimated, for example by measuring loop impedance, and that estimate does not include all contributions.

  • How Is the Breakdown Voltage of an Insulator Measured?

    The breakdown voltage of an insulator is determined by raising the test voltage until a disruptive discharge occurs, repeating the test and applying corrections for atmospheric conditions.

  • How is the calibration point of a sensor chosen?

    The calibration point is chosen according to how the sensor will be used: the points must cover the actual working range, include the most critical process value and be enough to reveal the sensor's behavior, which depends on whether it is linear or not.

  • How is the cell temperature of a module measured?

    The cell temperature of a module is not measured directly: it is obtained with a sensor attached to the back of the module and then corrected, or it is calculated from the open-circuit voltage and the temperature coefficient.

We do real tests, on video! Watch them on our YouTube channel →

Do you have a problem nobody has been able to measure?

Talk directly to the engineer in charge, with no middlemen.

Talk to an engineer