24/7 emergencies 814 777 6921812 230 6079WhatsApp 811 786 0768
Electrónica MonterreyElectrónica MonterreyLaboratorios Creativeit Talk to an engineer
Menu

Grounding

Clear explanations of concepts, methods, standards and measurements for engineers and technicians.

  • Copper or clad steel electrode?

    Copper offers greater corrosion resistance and good conductivity but costs more and is soft; copper-clad steel combines mechanical strength with copper at the surface, and its life depends on the cladding remaining intact.

  • Grid or perimeter ring?

    A grid controls voltages across its whole area thanks to its internal conductors; a perimeter ring surrounds the installation but leaves the interior without conductors of its own, so it is used in small areas or where the contact risk is low.

  • Ground testing with stakes or a clamp: when is each one the better choice?

    Measuring with stakes (fall of potential) is the better choice when the absolute value of an electrode or a grid is needed; the clamp suits quick checks on systems with several interconnected electrodes and no room to lay out probes.

  • How are power, control and communications grounds bonded together?

    Power, control and communications grounds are joined through a common grounding system and short equipotential bonds, so that there are no potential differences between them, and not through independent, unconnected grounds.

  • How does a clamp-on ground tester work?

    A clamp-on ground tester induces a voltage in a closed loop with one core, measures the resulting current with another and calculates the loop resistance, with no need to drive probes.

  • How does a three-pole and four-pole earth ground tester work?

    An earth ground tester injects alternating current between the electrode under test and an auxiliary electrode, measures the voltage at a probe and calculates the resistance; the three-pole version includes the connection lead in the reading and the four-pole version excludes it.

  • How is a deep ground electrode installed?

    A deep electrode is installed by drilling a borehole down to layers of lower resistivity, placing the electrode and backfilling so that it is in intimate contact with the soil and remains accessible for inspection.

  • How is a fall-of-potential measurement performed?

    The fall-of-potential measurement injects current between the electrode under test and a distant auxiliary electrode, and measures the voltage against an intermediate probe that is moved to find the zone of stable value.

  • How is a ground grid designed?

    Ground grid design starts from soil resistivity and fault current, and it is iterated until the calculated step and touch voltages fall below the tolerable limits.

  • How is a high-resistance ground improved?

    A high-resistance ground is improved by increasing contact with the soil: more well-spaced parallel electrodes, greater depth or extension, or treatment of the surrounding soil, after verifying the cause.

  • How is a photovoltaic system grounded?

    By bonding all conductive metal parts into an equipotential system connected to an electrode, and deciding whether the DC side is grounded or operated isolated with insulation monitoring, according to the inverter design and the regulations.

  • How is a substation protected from transferred voltages?

    By preventing a metallic conductor from connecting the substation's elevated-potential zone with a remote point, through equipotential bonding, insulation and separation of the systems that leave the site.

  • How is a tank or metal structure grounded?

    It is connected with bonding conductors to the ground grid to drain static charges and divert lightning and fault currents, ensuring continuity between all metal parts and compatibility with cathodic protection if present.

  • How is a telecommunications tower grounded?

    With an air termination and down-conductor system that carries the discharge to a low-impedance electrode, equipotential bonding of all legs, antennas, cables and shelters, and surge protection on every line entering the site.

  • How is an apparent soil resistivity curve interpreted?

    An apparent resistivity curve shows how the measured resistivity changes as the electrode spacing increases; its shape indicates whether the ground becomes more or less resistive with depth, but the apparent value is not the true resistivity of any layer.

  • How is resistivity measured in stratified soils?

    In stratified soil, resistivity is measured by repeating the four-electrode array at increasing spacings, and the apparent resistivity curve is interpreted to estimate the thickness and resistivity of each layer.

  • How is the continuity of a buried ground grid verified?

    The continuity of a buried grid is verified by measuring with a low-resistance ohmmeter between accessible points and a reference point on the grid, and comparing the values with one another.

  • How is the continuity of protective conductors measured?

    The continuity of protective conductors is measured with a low-resistance ohmmeter between the main grounding terminal and each exposed metal part or protective terminal, checking that the value is low and stable.

  • How is the current in a ground conductor measured?

    The current in a ground conductor is measured with a clamp meter that goes around the conductor without opening it, preferably a true-RMS model with sensitivity to small currents.

  • How is the grounding of a laboratory with sensitive equipment verified?

    By checking the continuity of the protective conductors, the electrode resistance, the location of the neutral-to-ground bond, and the potential differences and currents between the grounds that supply or reference the sensitive equipment.

  • How is the resistance of a transmission tower measured?

    The resistance of a transmission tower is measured with the fall-of-potential technique adapted to the tower's geometry, and it must be isolated from the effect of the shield wires, which place other towers in parallel.

  • How is the resistance of an electrode measured without disconnecting it?

    The resistance of an electrode can be measured without disconnecting it using methods that separate the electrode's current from the rest of the system, such as selective clamp measurement, or with a clamp that measures a closed loop.

  • How is the Wenner method applied for resistivity?

    The Wenner method measures soil resistivity with four electrodes in line and equally spaced: the outer ones inject current, the inner ones measure voltage, and an apparent resistivity is calculated.

  • How is touch voltage measured in a real installation?

    Touch voltage in a real installation is measured by injecting a known current into the ground grid and recording the voltage between the touched structure and a reference on the ground that simulates the feet, after which the result is scaled to the expected fault current.

  • Single ground or separate grounds for each system?

    Within one installation, a single grounding system is advisable or, if there are several electrodes, they should be interconnected with low impedance; separate grounds with no connection create dangerous potential differences during faults and lightning.

  • Vertical rod or horizontal electrode?

    It depends on how soil resistivity changes with depth: the vertical rod wins when the deep layers conduct better, and the horizontal electrode wins when the surface layer does.

  • What are step voltage and touch voltage?

    Step voltage is the potential difference between the two feet of a person standing on the ground; touch voltage is the one that appears between a structure touched by hand and the feet.

  • What causes unstable readings when measuring ground resistance?

    It is almost always one of three things: extraneous currents flowing in the soil, poor contact of the instrument's auxiliary stakes, or stakes placed within the electrode's zone of influence.

  • What does “ground loop” mean?

    It is a closed circuit formed by two or more ground connections of the same signal system; the potential difference between those grounds, or the magnetic flux crossing the loop, drives currents that appear as noise.

  • What does “grounding” mean?

    It is the intentional electrical connection of a system or piece of equipment to the mass of the earth through an electrode, to provide safety for people, a potential reference and a path for fault and discharge currents.

We do real tests, on video! Watch them on our YouTube channel →

Do you have a problem nobody has been able to measure?

Talk directly to the engineer in charge, with no middlemen.

Talk to an engineer