24/7 emergencies 814 777 6921812 230 6079WhatsApp 811 786 0768
Electrónica MonterreyElectrónica MonterreyLaboratorios Creativeit Talk to an engineer
Menu

Insulation and high voltage

Clear explanations of concepts, methods, standards and measurements for engineers and technicians.

  • How is the surface leakage current of an insulator measured?

    The surface leakage current of an insulator is measured by applying voltage and using a guard terminal to separate the current flowing over the surface from the current passing through the volume, or by monitoring in service the current that flows to ground through the insulator structure.

  • Measuring insulation at low or high voltage: what changes

    Measuring insulation at low voltage reveals contamination, moisture and severe deterioration with little risk, while measuring it at high voltage subjects the insulation to stress close to service conditions and can reveal local weaknesses, voids and non-linear behavior that the gentler test does not detect.

  • Online or Offline Partial Discharge Detection?

    Online detection measures partial discharges with the equipment in service and without interrupting it, while offline detection uses a controlled test source, which allows calibration and the determination of inception voltages.

  • Paper-Oil or Extruded Polymer Insulation?

    Oil-impregnated paper is a system of cellulose layers with a fluid, with a long track record and sensitive to moisture; extruded polymer is a continuous material, lighter and simpler to install, but sensitive to trees and voids.

  • What Are Creepage Distance and Clearance?

    Creepage distance is the shortest path along the surface of the insulator between two conductive parts; clearance is the shortest path through the air. The first controls tracking and the second controls sparkover.

  • What Causes Cable Failure from Electrical Treeing?

    An electrical tree forms through repeated partial discharges at a high-field point in polymeric insulation, which carve out branching channels until one crosses the material and causes the failure.

  • What Causes Discharges in Insulation Cavities?

    Discharges in insulation cavities occur because the gas inside the void has lower permittivity and lower dielectric strength than the surrounding solid, so the field in the cavity is higher and the gas ionizes.

  • What does “leakage current” mean?

    Leakage current is the small current that flows through or across insulation, or along an unintended path to ground, when voltage is applied.

  • What Does IEC 60085 Classify in the Thermal Rating of Insulation?

    The IEC 60085 standard classifies electrical insulation systems by their thermal endurance, assigning a class associated with the maximum continuous service temperature for which they are considered suitable.

  • What Does the IEC 60060-1 Standard on High-Voltage Techniques Cover?

    The IEC 60060-1 standard sets out general definitions, waveforms, test procedures and requirements for high-voltage test voltages: DC, AC, lightning impulse and switching impulse.

  • What Does the IEEE 400 Guide for Cables in the Field Describe?

    The IEEE 400 guide provides direction on field testing and insulation evaluation of shielded power cable systems, describing test types, methods and their application; it is a guide, not an acceptance specification.

  • What Does the IEEE 43 Guide for Rotating Machines Cover?

    IEEE 43 is a recommended practice that describes how to measure and interpret the insulation resistance of rotating machine windings, including the polarization index.

  • What Is a Disruptive Discharge?

    A disruptive discharge is the sudden collapse of the insulating capability between two electrodes, when a complete conductive channel forms between them; gases and liquids usually recover, while a solid is left with permanent damage.

  • What is a wall bushing?

    A wall bushing is a device that allows an energized conductor to pass through a grounded wall, tank or cover while insulating it electrically from that surface.

  • What Is an Acoustic Partial Discharge Detector?

    An acoustic partial discharge detector uses piezoelectric sensors to pick up the sound waves produced by a partial discharge, making it possible to detect and locate defects without being affected by electrical noise.

  • What Is an Electrostatic Voltmeter Used For?

    An electrostatic voltmeter measures voltage from the attractive force between charged electrodes, and is used to measure high DC and AC voltages while drawing practically no current.

  • What Is Dielectric Absorption?

    Dielectric absorption is the gradual increase in the polarization of an insulator when DC voltage is applied; it shows up as a current that decays over time and is used to judge whether the insulation is clean and dry.

  • What Is Insulation Coordination?

    Insulation coordination is the selection of the dielectric strength of equipment and of protective devices so that expected overvoltages rarely cause a failure.

  • What is partial discharge inception voltage?

    Partial discharge inception voltage is the lowest voltage at which, as the voltage is gradually raised, partial discharges above a defined magnitude threshold are detected. It depends on the defect, on the sensitivity of the measuring system and on the test conditions.

  • What is rated withstand voltage?

    Rated withstand voltage is the test voltage value that insulation must resist, without disruptive discharge, under standardized test conditions; it is not the operating voltage.

  • What Is Surface Tracking?

    Surface tracking is the formation of carbonized conductive paths on the surface of an insulator, caused by small leakage currents and discharges in the presence of contamination and moisture; the damage is permanent.

  • What is the basic impulse insulation level?

    The basic impulse insulation level, or BIL, is the peak value of the standardized lightning impulse voltage that insulation must withstand in a test.

  • What Is the Corona Effect?

    The corona effect is a localized electrical discharge in the air surrounding a conductor or a sharp point when the field at its surface exceeds what the air can withstand, without reaching a complete failure.

  • What is the dielectric frequency response of insulation?

    Dielectric frequency response describes how the capacitance and losses of an insulation change as the measurement frequency varies, normally over a wide range extending to very low frequencies. It is used mainly to estimate the moisture and conductivity of cellulose insulation impregnated with oil.

  • What Is the Dielectric Strength of an Insulator?

    Dielectric strength is the maximum electric field an insulator withstands before it loses its insulating capability and conducts; it is expressed as voltage per unit of thickness and is not a fixed constant of the material.

  • What is the thermal class of insulation?

    The thermal class of insulation is the maximum continuous operating temperature that its insulation system tolerates while reaching an expected service life, and it is designated by a letter.

  • Why do insulation readings change with ambient humidity?

    Insulation readings change with ambient humidity because moisture forms a conductive film on surfaces and can be absorbed by hygroscopic materials, opening leakage paths that reduce the measured resistance without the internal insulation necessarily being damaged.

  • Why Does a Porcelain Insulator Become Contaminated?

    A porcelain insulator becomes contaminated because wind deposits dust, salt and industrial residues on its surface, and light moisture turns them into a conductive layer that causes leakage and flashover.

  • Why Does Cable Termination Insulation Fail?

    Cable termination insulation fails because the termination is the point where the shield is cut and the electric field concentrates, so assembly defects, moisture or contamination can initiate discharges and leakage.

  • Why Does Insulation Fail from Prolonged Overheating?

    Prolonged overheating chemically degrades the insulation, which becomes brittle and loses dielectric strength and mechanical strength, until vibration, an overvoltage or moisture causes the failure.

We do real tests, on video! Watch them on our YouTube channel →

Do you have a problem nobody has been able to measure?

Talk directly to the engineer in charge, with no middlemen.

Talk to an engineer