24/7 emergencies 814 777 6921812 230 6079WhatsApp 811 786 0768
Electrónica MonterreyElectrónica MonterreyLaboratorios Creativeit Talk to an engineer
Menu

Power quality and Grid Code

Clear explanations of concepts, methods, standards and measurements for engineers and technicians.

  • What does “billing demand” mean?

    Billing demand is the amount of power, calculated according to the rules of the applicable rate, on which the demand charge is levied, and it does not always match the maximum measured demand.

  • What does “point of common coupling” mean?

    The point of common coupling, or PCC, is the point on the grid where one user's installation and other users connect, and where the effects of that installation on the others are evaluated.

  • What does effective value or true RMS mean?

    The true effective value, or true RMS, is the value of a signal that produces the same heating in a resistor as a direct current of that value, calculated from the actual waveform.

  • What does IEC 61000-4-30 define for measuring power quality?

    IEC 61000-4-30 defines how to measure power quality parameters in AC networks, with methods, aggregation intervals and performance classes so that measurements are comparable. It does not set acceptable limits.

  • What does IEEE 1159 classify on electromagnetic phenomena?

    IEEE 1159 is a recommended practice for monitoring electric power quality that classifies electromagnetic phenomena by category, typical duration and typical magnitude, and provides a common vocabulary for describing them.

  • What does IEEE 519 establish on harmonic distortion?

    IEEE 519 is a recommended practice that establishes how to limit harmonic distortion at the point of common coupling: it restricts the harmonic current each user injects and the voltage distortion the grid must maintain.

  • What Does Short Interruption Mean Compared with Sustained Interruption?

    The difference between a short interruption and a sustained interruption is the duration of the voltage loss and how service is restored: short ones recover on their own, usually through automatic reclosing; sustained ones require subsequent action.

  • What does THD mean?

    THD is total harmonic distortion: a ratio that compares the harmonic content of a waveform with its fundamental component and sums up in a single number how far it departs from a sine wave.

  • What features should a multifunction energy meter have?

    A multifunction energy meter must accurately measure voltage, current, power, energy and power factor, and also offer the logging, communication and configuration the application demands.

  • What is a Class A power quality analyzer?

    A Class A power quality analyzer is an instrument that meets the strictest method and uncertainty requirements of IEC 61000-4-30, so that two Class A instruments measuring the same signal give comparable results.

  • What is a split-core current transformer used for?

    A split-core current transformer is used to measure current without disconnecting the conductor: its core opens, is placed around the cable or busbar and closes, so that the conductor acts as a single-turn primary winding.

  • What is a synchrophasor and what device measures it?

    A synchrophasor is a voltage or current phasor, with magnitude and angle, measured against a common time scale, normally derived from GPS. It is measured by a device called a phasor measurement unit (PMU).

  • What Is a Voltage Sag and What Causes It?

    A voltage sag is a brief reduction in RMS voltage lasting from half a cycle to a few seconds, and it is almost always caused by a fault or by a large inrush current flowing through a shared impedance.

  • What is an equipment voltage sag tolerance curve?

    An equipment voltage sag tolerance curve is a graph of voltage magnitude against duration that marks out the zone in which a type of equipment usually operates without problems and the zones where it may fail, and it is used to assess the effect of recorded events.

  • What is flicker and what does the severity indicator measure?

    Flicker is the visual sensation of unsteadiness in a light source caused by voltage fluctuations, and its severity is quantified with indicators obtained from a standardized flicker meter, such as short-term severity Pst and long-term severity Plt.

  • What is power quality?

    Power quality describes how close the supply is to a stable sinusoidal voltage with suitable amplitude and frequency, and how well the load tolerates deviations.

  • What Is Reactive Power and Why Is It Compensated?

    Reactive power is the part of power that oscillates between the source and the magnetic or electric fields of the load without being converted into useful work; it is compensated to reduce the current flowing through the network and free up capacity.

  • What is the Código de Red and what does it cover on power quality?

    The Código de Red, Mexico's grid code, is the set of Mexican technical provisions on planning, operation and connection that establishes the efficiency, quality, reliability, continuity and safety criteria of the National Electric System. On quality, it sets requirements for voltage, frequency, harmonics and power factor.

  • What Is the Difference Between a Temporary Overvoltage and a Transient?

    A temporary overvoltage is an increase in RMS voltage lasting several cycles or more; a transient is a very brief, fast waveform disturbance that barely moves the RMS value.

  • What is the EN 50160 standard and what does it describe?

    EN 50160 describes the characteristics of the voltage supplied by public distribution networks, such as frequency, magnitude, dips, interruptions, harmonics and unbalance, and sets how far they must be maintained under normal operating conditions.

  • What Is the Negative-Sequence Component in a Three-Phase System?

    The negative-sequence component is the part of an unbalanced three-phase system that rotates in the opposite direction to the network; it does not exist in a perfectly balanced system, and in motors it produces heating and oscillating torques.

  • What is total demand distortion of current?

    Total demand distortion of current, TDD, is the root of the sum of the squares of the harmonic currents expressed as a percentage of the maximum demand load current, not of the instantaneous fundamental current.

  • What power quality does a data center require?

    A data center needs a supply that keeps the voltage within the tolerance of the computing equipment at all times, with continuous backup, redundancy, and control of harmonics and grounding.

  • Why Do Nonlinear Loads Distort the Waveform?

    A nonlinear load distorts the waveform because its current is not proportional to the applied voltage: it draws current during only part of the cycle, and that non-sinusoidal current breaks down into harmonics of the fundamental frequency.

  • Why do power factor correction capacitors heat up?

    Power factor correction capacitors heat up because they absorb harmonic currents that add to the fundamental, because of overvoltage, because of resonance with the grid, or because of internal losses in an aged or poorly ventilated capacitor.

  • Why do residual-current devices trip with no apparent fault?

    A residual-current device can trip with no apparent fault because it measures the sum of leakage currents, and that sum can grow because of filters, electronic equipment, or transients without any localized insulation damage.

  • Why do two analyzers report different harmonics in the same installation?

    Two analyzers can report different harmonics in the same installation because of differences in connection point, synchronization, calculation window, component grouping, averaging interval, accuracy class or sensors, or even because the load changed between measurements.

  • Why does a variable frequency drive fail when the DC bus voltage drops?

    A drive fails during a voltage drop because its inverter is fed from the DC bus, and when that bus falls below its minimum threshold the drive protects itself and trips on undervoltage.

  • Why does electronic equipment reset during brief voltage sags?

    Electronic equipment resets during brief voltage sags because its power supply can hold the DC voltage only as long as the energy stored in its capacitors lasts. If the sag lasts longer, the voltage falls below the minimum and the equipment resets or trips.

  • Why does resonance occur between capacitors and the grid?

    Resonance occurs between capacitors and the grid because the capacitance and the source inductance form a resonant circuit; at its frequency, the impedance seen by harmonic-producing loads becomes very high, and harmonic currents and voltages are amplified.

We do real tests, on video! Watch them on our YouTube channel →

Do you have a problem nobody has been able to measure?

Talk directly to the engineer in charge, with no middlemen.

Talk to an engineer