24/7 emergencies 814 777 6921812 230 6079WhatsApp 811 786 0768
Electrónica MonterreyElectrónica MonterreyLaboratorios Creativeit Talk to an engineer
Menu

Dielectric oils

Clear explanations of concepts, methods, standards and measurements for engineers and technicians.

  • Silicone oil or mineral oil as an insulating fluid?

    Silicone oil offers a high flash point and good thermal stability, so it is chosen where fire risk carries the most weight; mineral oil is more economical, has lower viscosity, and is backed by more experience and diagnostic knowledge.

  • What does “aniline point” mean?

    The aniline point is the minimum temperature at which equal volumes of aniline and oil mix completely; it indicates the aromatic content and, with it, the solvent power of the oil.

  • What does “hermetically sealed” mean?

    Hermetically sealed means that the transformer is built and operated with no exchange with the atmosphere: the oil stays isolated from the air, and its expansion is absorbed by the tank itself or by a flexible element.

  • What does ASTM D3487 cover for mineral insulating oils?

    ASTM D3487 is a specification standard for new mineral insulating oil for use in electrical apparatus; it sets the physical, electrical, and chemical properties the oil must meet before use.

  • What does IEC 60296 specify for new mineral oils?

    IEC 60296 is an international standard that specifies the requirements a new, unused mineral insulating oil must meet for transformers and switchgear, and the test methods associated with each requirement.

  • What does IEC 60599 say about dissolved gases?

    IEC 60599 is a guide to interpreting the analysis of dissolved and free gases in in-service electrical equipment insulated with mineral oil, and it proposes how to recognize fault types from the gases and their ratios.

  • What Does the Oil Do in a Transformer?

    Transformer oil performs several functions at once: it provides electrical insulation, carries heat from the core and windings to the radiators, impregnates the paper and serves as a source of diagnostic information.

  • What guidance does IEEE C57.104 give on gases in transformers?

    IEEE C57.104 is a guide to interpreting the gases generated in oil-immersed transformers, with criteria based on concentration, generation rate, and fault type for deciding on follow-up actions.

  • What is a furan?

    A furan is a cyclic organic compound containing one oxygen atom; in transformers, furan derivatives dissolved in the oil are markers of degradation of the cellulose insulation.

  • What is a particle counter used for?

    A particle counter measures how many particles are in a liquid and what size they are, normally by passing the fluid through a light beam and recording the signal from each particle that interrupts it; it is used to verify oil cleanliness.

  • What is a portable oil tester?

    A portable oil tester is a field instrument that uses an electrode cell and a high-voltage source to measure the voltage at which the oil breaks down dielectrically; portable units also exist for moisture and other rapid diagnostic tests.

  • What is a standardized oil test cell?

    A standardized oil test cell is a vessel with electrodes whose shape, material, and gap are defined by a standard, so that the measured breakdown voltage is comparable between laboratories and between samples.

  • What is an oil filtration machine?

    An oil filtration machine is a mobile unit that pumps oil through filters, and in some models through a heater and a vacuum chamber, to remove particles, water, and gases from insulating oil.

  • What Is an Oxidation Inhibitor in Oil?

    An oxidation inhibitor is an antioxidant additive that is gradually consumed to protect the insulating oil; while inhibitor remains, oxidation advances very slowly, and when it is depleted, oxidation accelerates.

  • What Is Corrosive Sulfur in Oils?

    Corrosive sulfur in oil is the presence of certain sulfur compounds that react with copper and form copper sulfide, a material that deposits on the insulating paper and can cause dielectric failures.

  • What Is Dissolved Gas Analysis?

    Dissolved gas analysis (DGA) measures the gases generated when thermal or electrical faults or cellulose degradation decompose the insulating oil, and it makes it possible to detect internal transformer problems without opening the unit.

  • What Is Oil Acidity and What Does It Indicate?

    Oil acidity, measured as the neutralization number, quantifies the acidic compounds formed by oxidation; a sustained increase indicates aging of the oil and a risk of sludge and attack on the cellulose.

  • What is pour point?

    Pour point is the lowest temperature at which an oil still flows when cooled under standardized test conditions; below it, the oil behaves like a semisolid.

  • What Is Sludge in Insulating Oil?

    Sludge in insulating oil consists of insoluble, polymerized oxidation products that deposit on windings, core and ducts, hindering cooling and accelerating the aging of the transformer.

  • What is the dielectric strength of insulating oil and what does it depend on?

    The dielectric strength of insulating oil is the maximum electric field intensity it withstands before a disruptive discharge occurs. In practice it depends mainly on water, particles and dissolved gases, more than on the chemical purity of the oil.

  • What is the dissipation factor of insulating oil and what does it reveal?

    The dissipation factor of insulating oil measures the fraction of energy the oil loses as heat when subjected to an alternating field. A rising value indicates the presence of polar contaminants, aging products or conductive particles.

  • What Is the Flash Point of Oil?

    The flash point is the lowest temperature at which the vapors of an oil, heated under defined test conditions, ignite momentarily when a flame is brought near them; it is used to assess fire safety and to detect contamination.

  • What Is the Interfacial Tension of Oil?

    Interfacial tension is the force of attraction at the contact surface between oil and water; it falls when the oil accumulates polar oxidation compounds, which makes it an early indicator of aging.

  • What is the oil quality index?

    The oil quality index is a number that combines properties such as interfacial tension and acidity to summarize the degree of aging; its exact definition varies with use, so it must be verified.

  • Why do laboratory results fail because of poor sampling?

    Results fail because of poor sampling because the sample stops being representative: it gains or loses water and gases, picks up dirt from the sampling point, or mixes with what is in the container.

  • Why does acetylene appear in oil?

    Acetylene appears when oil is exposed to very high temperatures, typical of an electric arc or a high-energy discharge, or when a tap changer transfers it to the main tank.

  • Why does hydrogen increase in oil?

    Dissolved hydrogen in oil increases because it is the first gas produced by almost all degradation mechanisms: partial discharges, localized heating and, sometimes, chemical reactions unrelated to a fault.

  • Why does oil become contaminated with fibers?

    Fibers reach the oil from the cellulose insulation itself, from mechanical wear, and from the handling of the oil or filters; with moisture they form bridges that reduce dielectric strength.

  • Why does oil form bubbles under load?

    Oil forms bubbles under load because heating releases dissolved gas or water vapor from the paper; these bubbles reduce dielectric strength and can initiate discharges.

  • Why does the same oil sample give different results between laboratories?

    The same oil sample gives different results between laboratories, in most cases, because the sample changed between one analysis and the other (water, gases, particles) or because the test methods and conditions are not identical. The uncertainty inherent in the method explains the rest.

We do real tests, on video! Watch them on our YouTube channel →

Do you have a problem nobody has been able to measure?

Talk directly to the engineer in charge, with no middlemen.

Talk to an engineer