Technical guides
Clear explanations of concepts, methods, standards and measurements for engineers and technicians.
- Antennas 52
- Confined spaces 52
- Dielectric materials 54
- Dielectric oils 61
- Electric vehicles 52
- Electrical safety and PPE 52
- Electronic instrumentation 52
- EMC/EMI 53
- Environmental testing 53
- Grounding 54
- Industrial electrical systems 52
- Insulation and high voltage 61
- Metrology and calibration 59
- Oscilloscopes 53
- Power quality and Grid Code 61
- RF and microwave 61
- Solar energy 52
- Temperature and pressure 52
- Thermography 53
- Transformers 55
- Troubleshooting 52
- Vibration 52
- Wireless communications 52
- How Do You Decide Between Repairing or Replacing an Aging Transformer?
The decision combines the actual condition of the insulation and the components, the criticality of the unit, the availability of repair and the total cost over the remaining life, not a single test or the age alone.
- How do you decide when to degas a transformer?
The decision to degas is made when the oil contains gases or moisture that are no longer justified and the cause of their generation is under control; doing it before understanding the fault erases diagnostic information.
- How Do You Decide Whether an Instrument Conforms Using Uncertainty?
To decide conformity, the measured result is compared with the tolerance limit by applying an agreed decision rule that takes measurement uncertainty into account and defines when the result is accepted, rejected or left undetermined.
- How do you determine whether harmonic distortion comes from the load or the network?
To find out whether harmonic distortion comes from the load or the network, compare how harmonic voltage and current vary as the load changes, the direction of harmonic power flow and the background distortion present with the load disconnected.
- How do you diagnose a circuit board that resets itself?
A circuit board that resets itself usually has a power, clock or watchdog problem, or a noise or heat problem. The diagnosis consists of capturing the instant of the reset and determining which line or event precedes it.
- How do you diagnose a motor that trips its protection?
A motor that trips its protection is diagnosed by determining which type of protection is operating (overload, short circuit, ground fault or imbalance) and comparing the actual current with the rated current, the condition of the insulation and the mechanical condition of the load.
- How do you diagnose a power supply that will not turn on?
To diagnose a power supply that will not turn on, check the input, the protection, the rectification, the control stage and the outputs in that order, separating a supply that is actually damaged from one that is protecting itself against a shorted load.
- How Do You Diagnose a Transformer After an External Fault Trip?
First identify which protection operated and what current flowed, then compare electrical, oil and mechanical response tests against reference values to decide whether there was damage before re-energizing.
- How do you diagnose a variable frequency drive with a recurring fault?
A drive with a recurring fault is diagnosed by first reading the fault code and event history, then checking that fault against the input supply, the motor load, the environment and the configuration, because the cause almost always lies outside the electronics themselves.
- How do you enter a sewer or manhole?
A sewer or manhole is entered only after treating it as a confined space: open and ventilate it, measure the atmosphere, control the flow and traffic, and enter with a permit, harness, attendant and rescue plan.
- How do you enter a transformer tank for internal inspection?
To enter a transformer tank, treat it as a confined space: de-energize and isolate it, confirm that the air is breathable, ventilate, measure the oxygen and have an attendant, a permit and rescue in place.
- How do you find an intermittent fault with an oscilloscope?
To find an intermittent fault, configure the oscilloscope to capture only the abnormal event, with a selective trigger, long memory and persistence or segmented modes, and leave it recording until the event occurs.
- How do you inspect a silo or hopper?
Inspecting a silo or hopper involves its own risks: engulfment by material, a deficient or explosive atmosphere, combustible dust, and material that sticks and then falls. That is why it is emptied, isolated and locked out, and entered only with a permit and a harness.
- How do you integrate an instrument with remote commands?
An instrument is integrated with remote commands by sending it text instructions over its communication interface, normally in the SCPI language through a layer such as VISA, and synchronizing each command with the completion of the action.
- How Do You Interpret the Insulation Resistance Trend Over Time?
The insulation resistance trend is interpreted by comparing readings from the same equipment, taken under equivalent conditions and corrected for temperature; the direction and speed of the change matter more than an isolated value.
- How do you isolate a fault in a circuit by bisection?
Isolating a fault by bisection consists of dividing the circuit into two halves, measuring at the midpoint to find out which half contains the defect, and repeating with that half until it is located.
- How Do You Locate a Fault in an Underground Cable?
A fault in an underground cable is located in stages: confirm the type of fault, estimate its distance from one end, and finally pinpoint it along the route.
- How Do You Locate an Interference Source with a Directional Antenna?
An interference source is located by moving a directional antenna and watching on a spectrum analyzer where the signal is strongest: the direction is obtained by taking a bearing, and the position by triangulation from several points.
- How do you make a floating measurement with an oscilloscope?
A floating measurement is one in which no point in the circuit is referenced to ground. It is made with a differential probe or an oscilloscope with isolated channels, and not by disconnecting the instrument's ground, which is a dangerous practice.
- How do you measure a very high resistance without leakage?
To measure a very high resistance without leakage, you must keep stray currents through insulators, surfaces and cables from flowing through the instrument, using guarding, shielding and quality insulators, and waiting for settling.
- How do you measure a very low resistance?
To measure a very low resistance, use a four-wire connection, a test current that is sufficient but controlled, and compensation of thermoelectric voltages, because at these values the wiring and contacts weigh as much as the component.
- How do you measure a very small current?
A very small current is measured with a feedback picoammeter or electrometer, or with a very high-resolution multimeter on its lowest range, taking care with leakage, noise and the voltage drop the instrument introduces.
- How do you measure current in a conductor without opening the circuit?
To measure current without opening the circuit, a clamp-on current probe is used that measures the magnetic field around a single conductor, so the circuit remains intact and insertion is minimal.
- How do you measure dead time in a power inverter?
The dead time of an inverter is the interval during which both switches in the same leg are off; it is measured by comparing the gate signals of both with probes that tolerate the floating reference of the high-side switch.
- How do you measure frequency with a universal counter?
To measure frequency with a universal counter, connect the signal to the appropriate input, set the coupling, impedance and trigger level, and choose a gate time that gives the desired resolution, with a stable time base.
- How do you measure instantaneous power with voltage and current?
Instantaneous power is the product of voltage and current at each instant; the oscilloscope calculates it by multiplying two channels, provided the two signals are aligned in time.
- How do you measure overshoot and settling?
Overshoot is how far the peak exceeds the final value of a transition, expressed as a percentage of the step amplitude, and settling is the time the signal takes to remain within a tolerance band around that final value.
- How do you measure the capacitance of an in-circuit component?
To measure the capacitance of a component in circuit, you must discharge and de-energize the circuit and keep in mind that the other components connected in parallel also contribute to the measured value.
- How do you measure the noise and ripple of a power supply?
Power supply noise and ripple are measured with AC coupling, a minimal ground connection and a defined bandwidth, because the result depends more on how the probe is connected than on the instrument.
- How do you measure the phase shift between two signals?
The phase shift between two signals is obtained by measuring the time delay between equivalent points on both and dividing it by the period: the phase shift in degrees is 360 times that quotient.