24/7 emergencies 814 777 6921812 230 6079WhatsApp 811 786 0768
Electrónica MonterreyElectrónica MonterreyLaboratorios Creativeit Talk to an engineer
Menu

Industrial electrical systems

Clear explanations of concepts, methods, standards and measurements for engineers and technicians.

  • What Does NOM-001-SEDE Cover?

    NOM-001-SEDE is the Mexican official standard that sets the safety requirements for electrical utilization installations, that is, those on the load side after the supply delivery point.

  • What Does the IEEE 242 Protection Standard Cover?

    IEEE 242 is a recommended practice on the protection and coordination of industrial and commercial power systems: it explains how to select and set protective devices so that they clear faults with the least possible damage and interruption.

  • What does the neutral grounding scheme of an installation mean?

    The neutral grounding scheme describes how the source neutral is connected to ground and how the metal parts of the installation are grounded, and the fault current and the way of protecting the installation depend on it.

  • What Is a Busbar or Bus?

    A busbar, or bus, is a rigid conductor or a set of them that gathers and distributes current among several circuits connected at the same electrical point; in network studies, “bus” also designates that node in the model.

  • What Is a Hall Effect Current Transducer?

    A Hall effect current transducer measures current from the magnetic field it produces, using a semiconductor sensor that generates a voltage proportional to that field, and it works with both alternating and direct current.

  • What is a motor control center?

    A motor control center, or MCC, is a set of standardized units inside a modular enclosure that groups the starters, protections, and controls of several motors, fed from a common bus.

  • What Is a Numerical Protection Relay?

    A numerical protection relay is a microprocessor-based device that samples currents and voltages, converts them to numbers, calculates quantities and executes protection functions in software instead of through electromechanical mechanisms.

  • What is a short-circuit study?

    A short-circuit study calculates the currents that would flow through each point of an installation during a fault, to confirm that equipment and protections can withstand and interrupt those currents.

  • What is a single-line diagram and what is it used for?

    A single-line diagram is a simplified representation of a three-phase electrical installation with one line per circuit, showing how sources, transformers, protections, and loads are connected.

  • What Is Coincident Demand?

    Coincident demand is the maximum of the sum of several loads measured at the same instant, and it is always less than or equal to the sum of their individual maximum demands, because peaks rarely occur at the same time.

  • What is ground fault current and how is it limited?

    Ground fault current is the current that flows to ground when an energized conductor loses its insulation, and its value is determined mainly by the impedance through which the system neutral is grounded.

  • What is load flow in an industrial installation?

    Load flow is the steady-state calculation of voltages, currents, and power at every point of an installation, given the loads and sources, to verify that the network operates within its limits.

  • What Is NFPA 70B and What Is It For?

    NFPA 70B is the standard on electrical equipment maintenance: it describes how to structure a preventive maintenance program, what to inspect and test, and what criteria to use in deciding the frequency.

  • What is protection coordination?

    Protection coordination is the setting of an installation's protective devices so that, during a fault, the closest device operates first and the rest remain as backup, without leaving equipment unprotected.

  • What is selectivity between circuit breakers?

    Selectivity between circuit breakers is the property by which, during an overcurrent, only the breaker immediately upstream of the fault opens and the others remain closed.

  • What Is the Service Factor of a Motor?

    A motor's service factor is a multiplier of rated power that indicates how much additional load it can handle continuously, under rated voltage, frequency and ambient conditions, with acceptable heating.

  • What Short-Circuit Calculation Method Does IEC 60909 Describe?

    IEC 60909 describes a method for calculating short-circuit currents in three-phase AC networks based on an equivalent voltage source at the fault location, with no need for a prior load flow study.

  • Why Do Connection Points in a Panel Heat Up?

    A connection heats up because its contact resistance is higher than intended, and the current passing through it generates heat proportional to that resistance and to the square of the current.

  • Why Does a Circuit Breaker Trip Without an Apparent Overload?

    A circuit breaker can trip without a sustained overload because it responds to peaks, heat, ground leakage or incipient faults that a multimeter does not show at a given instant.

  • Why Does a Contactor Fail from Sparking at Its Contacts?

    Sparking at a contactor's contacts indicates that an arc is forming on closing or opening, usually because of low coil voltage, contact bounce, wear, or a load more severe than its utilization category allows.

  • Why Does a Motor Burn Out from Loss of a Phase?

    When a phase is lost, the three-phase motor keeps turning as if it were single-phase: the current in the remaining phases increases and the negative-sequence component rapidly heats the rotor and windings until the insulation is damaged.

  • Why Does the Insulation of a Motor Fed by a Variable Frequency Drive Fail?

    Drives apply voltage pulses with very fast edges to the motor; on long cables, reflections raise the voltage at the terminals and concentrate the stress in the first turns of the winding, eventually causing partial discharges and insulation failure.

We do real tests, on video! Watch them on our YouTube channel →

Do you have a problem nobody has been able to measure?

Talk directly to the engineer in charge, with no middlemen.

Talk to an engineer