24/7 emergencies 814 777 6921812 230 6079WhatsApp 811 786 0768
Electrónica MonterreyElectrónica MonterreyLaboratorios Creativeit Talk to an engineer
Menu

RF and microwave

Clear explanations of concepts, methods, standards and measurements for engineers and technicians.

  • What are S-parameters?

    They are the coefficients that describe how a device with one or more ports reflects and transmits incident waves; each parameter is the complex ratio between a wave leaving one port and a wave entering another.

  • What are unconditional amplifier stability and the K factor?

    An amplifier is unconditionally stable when it does not oscillate with any passive source or load impedance at a given frequency; the Rollett criterion verifies this with a K factor greater than one together with an S-parameter determinant of magnitude less than one.

  • What Causes Precision Connector Wear?

    Wear comes from connection cycles, dirt acting as an abrasive, excessive or misaligned tightening, and mating with damaged connectors or connectors of different tolerances. It changes critical dimensions and degrades repeatability.

  • What Causes Saturation of an Analyzer’s Receiver?

    It is caused by an input signal too strong for the first mixer or the analog-to-digital converter, which leaves its linear region and generates harmonics and intermodulation products that do not exist in the real signal.

  • What Do the ITU Radio Regulations Govern?

    They are the international treaty that divides the radio spectrum among radiocommunication services and sets rules for using frequencies and orbits without causing harmful interference between countries.

  • What does dBm mean?

    dBm is the power level expressed in decibels relative to one milliwatt. Zero dBm equals one milliwatt, and every ten decibels up or down multiplies or divides the power by ten.

  • What Does the IEC 60153 Standard for Waveguides Cover?

    IEC 60153 is a series of standards on hollow metallic waveguides: general requirements, measurement methods and specific dimension and tolerance specifications for the most widely used waveguide types.

  • What Does the IEC 61169 RF Connector Series Cover?

    The IEC 61169 series brings together international specifications for radio-frequency coaxial connectors: a generic part with definitions and test methods, and specific parts for each connector family.

  • What Does the IEEE 1785 Standard for Waveguides Define?

    IEEE 1785 is a family of standards that establishes band designations, dimensions, flange interfaces and performance requirements for metallic rectangular waveguides at very high millimeter-wave and submillimeter-wave frequencies.

  • What Is a Coaxial Termination Load?

    A coaxial termination load is a one-port component that presents a resistance equal to the characteristic impedance of the line and absorbs the energy reaching it, so that almost nothing is reflected.

  • What is a mechanical calibration kit and which standards does it contain?

    A mechanical calibration kit is a set of standards of known impedance (open, short, matched load and thru) with which a vector network analyzer corrects its systematic errors; each connector type and gender requires its own kit.

  • What Is a Power Meter with a Sensor Used For?

    It measures, accurately and with traceability, the absolute power reaching a sensor, regardless of frequency selectivity; the sensor converts RF power into an electrical signal and the meter processes and displays it.

  • What Is a Vector Network Analyzer?

    It is an instrument that generates a signal, applies it to a device and uses coherent receivers to measure the magnitude and phase of the reflected and transmitted waves, yielding the device's S-parameters as a function of frequency.

  • What is a waveguide?

    It is a hollow metal structure, normally rectangular or circular, that guides microwave electromagnetic waves with very low loss; it propagates signals only above a cutoff frequency that depends on its dimensions.

  • What is return loss?

    It is the measure, in decibels, of how much incident power is returned by reflection: the higher the value, the lower the reflection and the better the match.

  • What is the characteristic impedance of a line?

    It is the ratio between voltage and current of a wave traveling in a single direction along the line; it depends on the geometry and the dielectric, not on the length, and it determines whether a load produces reflections.

  • What is the compression point of an amplifier?

    It is the power level, input or output, at which the actual gain of the amplifier falls one decibel below its linear gain; it marks the onset of saturation and the practical limit of linear operation.

  • What is the cutoff frequency of a waveguide?

    The cutoff frequency of a waveguide is the minimum frequency at which a mode can propagate through it; below it, the field decays exponentially and carries no power. In a rectangular guide with the dominant mode, it depends on the larger dimension of the cross-section.

  • What is the decibel and why is it used in RF?

    The decibel is a logarithmic scale for expressing the ratio between two powers. It is used in RF because signals span many orders of magnitude and because cascaded gains and losses add instead of multiplying.

  • What is the ISM band?

    ISM bands are frequency ranges set aside internationally for industrial, scientific and medical applications that use radio frequency energy for purposes other than communication. Many short-range communication devices share them under certain conditions.

  • What is the noise figure of a receiver or amplifier?

    Noise figure indicates how much the signal-to-noise ratio degrades when a signal passes through a receiver or amplifier: it is the ratio of the input signal-to-noise ratio to the output signal-to-noise ratio, normally expressed in decibels.

  • What is the noise floor?

    The noise floor is the power level below which a signal cannot be distinguished from the random fluctuations of the measurement system itself. It depends on thermal noise, the receiver noise figure and the measurement bandwidth.

  • What is the phase noise of an oscillator?

    It is the measure of the random phase fluctuations of an oscillator, seen as noise sidebands around the carrier; it is expressed as power in a one-hertz band relative to the carrier, as a function of frequency offset.

  • What is the reference plane in a measurement?

    It is the position along the signal path to which the results of a measurement are referred. Everything before that plane is corrected or excluded; everything after it is part of what is measured.

  • What is the standing wave ratio?

    It is the ratio between the maximum and minimum voltage of the standing wave that forms on a line when part of the signal is reflected at the load; it equals one with a perfect match and grows as reflection increases.

  • What is third-order intermodulation?

    It is the distortion that appears when two signals of nearby frequencies pass through a nonlinear device and generate products at 2f1−f2 and 2f2−f1, which fall next to the original signals and cannot be filtered out easily.

  • Why do flexible test cables degrade VNA calibration?

    Flexible test cables degrade the calibration of a vector network analyzer because, when moved, their electrical length, loss and match change, and calibration assumes those characteristics stay the same as when the standards were measured.

  • Why Does a VSWR Measurement Change When the Cable Moves?

    Because the cable is part of the measurement chain: flexing it changes its phase, its loss and the quality of its connectors, and a calibration made with the cable in another position no longer corrects those changes.

  • Why Does Incorrect Connector Torque Make a Measurement Fail?

    Because torque defines how well the contact surfaces join. Too little tightening leaves an irregular, reflective contact; too much deforms the connector and shifts the reference plane. In both cases the measurement stops being repeatable.

  • Why Does the Analyzer Show a Noisy Trace?

    Usually because the signal is close to the instrument's noise floor or because the resolution and video filters are too wide. Narrowing them, averaging or lowering the input attenuation usually cleans up the trace.

We do real tests, on video! Watch them on our YouTube channel →

Do you have a problem nobody has been able to measure?

Talk directly to the engineer in charge, with no middlemen.

Talk to an engineer