24/7 emergencies 814 777 6921812 230 6079WhatsApp 811 786 0768
Electrónica MonterreyElectrónica MonterreyLaboratorios Creativeit Talk to an engineer
Menu

EMC/EMI

Clear explanations of concepts, methods, standards and measurements for engineers and technicians.

  • What does the IEC 61000-4-3 radiated immunity standard cover?

    IEC 61000-4-3 describes the test method for the immunity of electrical or electronic equipment to radiated radio-frequency electromagnetic fields: how to generate and calibrate the field, how to apply it to the equipment and how to classify the result. Test levels are set by the product standard.

  • What does the IEC 61000-4-4 fast burst standard cover?

    IEC 61000-4-4 describes the immunity test for electrical fast transient bursts: the generator, the coupling networks and clamps, the arrangement over a reference plane and the classification of the result. Levels and criteria are defined by the product standard.

  • What does the IEC 61000-4-5 surge standard cover?

    IEC 61000-4-5 describes the immunity test for unidirectional surges caused by switching and by indirect lightning: the combination wave generator, the coupling networks, the line-to-line and line-to-ground modes, and the evaluation. Levels are set by the product standard.

  • What is a ground reference plane in EMC?

    A ground reference plane in EMC is a large conductive surface that serves as a common potential reference and as a low-impedance return path for high-frequency currents, both in a design and in a test setup.

  • What is a lightning surge transient in immunity testing?

    It is a high-energy overvoltage of relatively long duration (microseconds to hundreds of microseconds) applied to the lines of a piece of equipment to simulate the indirect effects of lightning and switching operations on the network. Unlike fast bursts, it can destroy components.

  • What is a line impedance stabilization network?

    It is a device inserted between the power network and the equipment under test to provide a defined, repeatable impedance at the measurement frequencies, isolate the setup from network noise and deliver the disturbance from the equipment to a receiver.

  • What is a pulse generator for immunity testing?

    An immunity pulse generator is an instrument that produces a transient disturbance with a standardized waveform: it charges a storage capacitor and discharges it through a shaping network and a switch, so that the pulse delivered to the equipment is repeatable and verifiable.

  • What is a TEM cell?

    A TEM cell is a flared rectangular transmission line, with a flat center conductor (septum) and metal outer walls, that generates a nearly uniform electromagnetic field inside. It is used to test small equipment for immunity or to measure its emission without a large chamber.

  • What is an absorbing clamp used for?

    It is used to measure the disturbance power that equipment sends along its power cord or other cables at frequencies where measuring the radiated field is inconvenient. It is slid along the cable until the maximum is found, and it replaces the antenna as the evaluation method.

  • What is an electrical fast transient burst?

    An electrical fast transient burst is a train of very short pulses, with nanosecond rise times, repeated in packets. It represents the noise from switching inductive loads and is used to check that equipment does not reset or lock up.

  • What is an EMI receiver and how does it differ from a spectrum analyzer?

    An EMI receiver is a selective measuring instrument designed to meet the requirements of emissions standards: it has defined preselection, bandwidths and detectors. A spectrum analyzer is more general, faster and more flexible, but it needs preselection and accessories to match the reliability of the receiver.

  • What is an EUT?

    EUT stands for "equipment under test": the specific product, in a defined configuration, that is subjected to an emission or immunity test.

  • What is common impedance coupling?

    Common impedance coupling occurs when two circuits share a section of conductor, such as a ground or a power supply, and the current of one produces a voltage drop across that shared impedance that appears as noise in the other.

  • What is electromagnetic compatibility?

    Electromagnetic compatibility is the ability of equipment or a system to function satisfactorily in its electromagnetic environment without producing intolerable disturbances for others or being affected by those in its environment.

  • What is electromagnetic immunity?

    Electromagnetic immunity is the ability of equipment to keep operating without unacceptable degradation when exposed to electromagnetic disturbances such as electrostatic discharges, radio fields, fast transients or voltage dips.

  • What is shielding effectiveness?

    Shielding effectiveness measures how much a metal barrier attenuates an electromagnetic field: it is the ratio, in decibels, between the field without the shield and the field with the shield at the same point.

  • What is the difference between conducted and radiated emissions?

    Conducted emission is the disturbance that equipment injects into its cables, above all into the power network, and it is measured at low frequencies with a stabilization network; radiated emission is what leaves through the air as a field and is measured with an antenna.

  • What is the immunity performance criterion?

    The immunity performance criterion is the definition, agreed before the test, of how much degradation of its function is acceptable in a device during and after a disturbance; it turns "failed" or "did not fail" into an objective decision.

  • Why do long cables radiate more?

    Because a long cable picks up and emits energy more efficiently when its length is a significant fraction of the wavelength. At low frequencies, a short cable is a poor radiator; as frequency increases, the same cable eventually resonates and becomes an efficient antenna.

  • Why does a microcontroller reset when a nearby relay is activated?

    Because when the relay coil or contacts open, a transient appears that couples to the microcontroller through the power supply, through the shared ground or through the field, and causes a voltage drop or a pulse on a sensitive line that triggers the reset.

  • Why does a shield with apertures lose effectiveness?

    Because an aperture lets the field through and, at some frequencies, behaves like a slot antenna. What counts is the largest dimension of the aperture relative to the wavelength, not its area: a long, narrow slot leaks more than several small holes of the same total area.

  • Why does an emissions test fail only at certain frequencies?

    An emissions test fails only at certain frequencies because emissions are usually narrowband signals, such as clocks, power supply switching and their harmonics, amplified by resonances of cables, apertures or structures that act as efficient antennas at those frequencies.

  • Why does equipment fail emissions even when its design is correct?

    Because the schematic does not include what determines the emission: current return paths, parasitic inductances, loop area, connected cables and the mechanical assembly. An electrically correct circuit can be a good antenna if its physical construction allows it.

We do real tests, on video! Watch them on our YouTube channel →

Do you have a problem nobody has been able to measure?

Talk directly to the engineer in charge, with no middlemen.

Talk to an engineer