24/7 emergencies 814 777 6921812 230 6079WhatsApp 811 786 0768
Electrónica MonterreyElectrónica MonterreyLaboratorios Creativeit Talk to an engineer
Menu

75 Ω Testing and Characterization with a VNA Network Analyzer

Electrical characterization of 75 Ω cables, connectors, filters and other RF components with a vector network analyzer (VNA), for engineering, quality and maintenance.

Graph of S-parameter measurements of a 75 Ω device with a VNA network analyzer

Analysis of 75 Ω RF devices and systems

We perform electrical characterization tests on devices, components, cables and systems with a characteristic impedance of 75 Ω. We use a vector network analyzer (VNA) and specialized accessories to measure S-parameters with traceability and controlled test conditions.

75 Ω systems are widely used in cable television, CATV, RF video, telecommunications, signal distribution, coaxial infrastructure and radio-frequency systems. Good characterization determines the losses, reflections, impedance matching and frequency behavior of the elements under test.

The service applies to individual components, coaxial cables, connectors, adapters, filters, splitters, couplers and other 75 Ω passive RF devices.

Analysis using S-parameters

The VNA analyzes the behavior of the device as a function of frequency. Depending on the configuration, S11, S21, S12 and S22 are obtained, to evaluate both reflections and transmission through the device.

The quantities that can be analyzed include return loss, VSWR, insertion loss, attenuation, transmission, reflection and phase.

These measurements make it possible to identify impedance matching problems, excessive losses, discontinuities, resonances and variations in electrical behavior within the evaluated frequency range.

Measurement system for 75 Ω

The measurement system is configured according to the device under test. The setup can incorporate RF adapters, type N and type F connectors, phase-stable coaxial cables and calibration elements.

Phase-stable cables are especially important when repeatable measurement conditions are required after calibration. They reduce the changes caused by moving or handling the cable when connecting the device.

Depending on the configuration and the available equipment, we use eCal electronic calibration or mechanical calibration, with the standards corresponding to the measurement system.

Calibration before testing

Before measuring, the reference plane of the system is established with the corresponding calibration procedure. This can include Open, Short, Load and Thru standards, or an eCal module when compatible with the VNA and the configuration used.

Calibration compensates for systematic errors in the analyzer, cables, connectors and interconnecting elements. At 75 Ω it is especially important to control the transition between connector types and to keep a consistent mechanical configuration throughout the measurement.

75 Ω coaxial cable testing

We characterize 75 Ω coaxial cables. Depending on the test, insertion loss, return loss, VSWR, frequency response and phase behavior can be evaluated.

VNA measurement analyzes the cable over a wide frequency range and detects changes that a continuity or DC resistance measurement does not reveal. Cables, connectors, terminations or manufacturing lots can also be compared under equivalent conditions.

RF component testing

The service applies to 75 Ω passive components, including:

  • RF adapters and transitions.
  • Coaxial connectors.
  • Coaxial cables and assemblies.
  • Filters.
  • Attenuators.
  • Signal splitters.
  • Couplers.
  • Passive CATV devices.
  • Signal distribution elements.
  • Components used in RF video systems.

The test is configured according to the characteristics of the device, the number of ports, the available connectors and the required frequency range.

Applications

75 Ω testing serves quality control, incoming material inspection, product development, component comparison, fault diagnosis, cable validation and RF system verification. We also perform comparative measurements between a reference sample and a sample under evaluation, to identify differences between apparently identical components.

Service deliverables

Depending on the requested scope, the service can include VNA measurement files, S-parameter graphs, results tables and a technical report with the test conditions. Results are presented as a function of frequency and can show magnitude, phase, VSWR, return loss, insertion loss or other derived parameters.

The scope, frequency range, calibration type and reported parameters are defined according to the equipment or component being evaluated.

75 Ω measurement service

Request a quote, stating the device type, connectors, frequency range and number of samples.

We do real tests, on video! Watch them on our YouTube channel →

Do you have a problem nobody has been able to measure?

Talk directly to the engineer in charge, with no middlemen.

Talk to an engineer